Product Details: No-slip Tapes, Outdoor Stairs
Slipping on the stairs is no fun. Use our peel-N-stick No-slip Tapes to prevent accidents.
Traction near the edge of each step so your foot does not slip.
Easy Peel-N-Stick design makes installation a breeze. Hand-peel, with some effort, to remove. In our testing there was no damage to the stair treads. Request Free Evaluation Samples. No purchase necessary. We stock many colors. Custom sizes available. Orders ship along with free samples. Spend $80 or more and get Free Shipping (via United States Postal Service and within continental United States), Exclusions Apply. International Shipping - Canada, UK, Australia, and more.
CERTIFIED TRACTION: Non-slip traction is certified by the National Floor Safety Institute (NFSI) and also exceeds OSHA and ADA safety standards.
NOT RECOMMENDED for submerged surfaces. For areas with heavy snow and significant dampness/wetness we recommend the No-slip Mats solution.
CONFORMABLE NO-SLIP TAPES: Our conformable No-slip Tapes adhere to irregular surfaces like diamond mesh stair treads. Any other peel-N-stick solution will start to lift in a short time because they are not designed for irregular surfaces. Use our peel-N-stick conformable No-slip Tapes instead. During installation, you will need to use a rubber mallet to gently tap on the strip so that it properly adheres to the irregular surface.
IMPORTANT NOTICE TO USER: Our solution balances safety, ease of application, and removal. However user is solely responsible for evaluating the product and determining suitability. Every order ships with free samples for you to evaluate installation and removal. On most surfaces you should be able to hand-peel, with some effort, to remove. You may request free samples prior to ordering No-slip Tapes. Please use sample and test in an inconspicuous location to determine suitability on your surface.
We have various sizes and colors available. Both Rolls and Pre-cut lengths are available. We stock the following pre-cut lengths (standard width is 2 inches unless otherwise specified): 10 inches, 13", 16", 19", 22 ", 25", 28", 31", 34", 37", 40", 43", 46", 49", 52", 55", 58", and 61 inches.
Rolls are always 720 inches in length. We stock the following widths for the rolls: 2", 4", and 6 inches.
Parallel Strips Application (optional recommendation): You can achieve more surface area coverage by installing two or more strips in parallel and
Pricing is per pre-cut strip or per roll. Both options give you the flexibility to order only what you need. Longer lengths (i.e. for the pre-cut strips) and wider widths (i.e. for the rolls) cost a bit more. Price also vary for certain colors. You will see total price when you go to View Cart.
How To Order
Step 1. Measure the length of each step (longest side of step) and subtract two inches. The result should be the pre-cut length to order. So if your step measure at 33 inches in length, then subtract two inches and order the 31 inches pre-cut length. It is ok to order a smaller length and we recommend not exceeding your maximum calculated length. You may also order a Roll and cut to size with scissors.
Step 2. Choose a color. See Colors.
Step 3. Go to the order page and choose the Product Type, Size, Color, and Quantity, and then Click the green "Add to Cart" button and complete Checkout.
Step 1. Clean surface. Surface must be clean, dry, and in good repair. Repair any damaged surfaces. Remove oils, dirt and flaking paint. Do not install on any large cracks, pits, or grout lines. Surface temperature must be above 60˚F.
Note: Porous surfaces like untreated wood and concrete should be sealed with a primer like our Surface Sealer. This will prevent water from degrading the adhesive over the years. Using supplied brush, apply only a thin film of Surface Sealer to where you’ll install No-slip Tapes and let dry. On a nice sunny day it takes about 5 minutes for the Surface Sealer to dry. Our 17 ounce Surface Sealer will cover up to 25 square foot. Therefore it is adequate for most projects.
Step 2. Peel backing paper from product and place No-slip Tape about 0.5" (half an inch) from edge of step. We do not recommend that you install it right on the edge. Doing so will reduce product life. Do not install on a curved surface. Use a Roller to activate adhesive.
Note: Apply our optional Edge Sealer to seal the edges of No-slip Tapes and prevent moisture from going underneath and degrading the adhesive over the years. Only a very small amount is needed. A single tube of our Edge Sealer will cover 120 feet - more than adequate for most projects. You'll need to apply only a very small amount around the edges of your installed No-slip Tapes. Simply remove the cap off the Edge Sealer to expose the nozzle. Point nozzle to edge of installed No-slip Tape and move nozzle around all edges while at the same time pressing gently on tube to allow a bead of Edge Sealer to come out and seal the edges of No-slip Tape. Allow 5 minutes to dry. You only need a thin film around the edges.
Step 3. Optional. Repeat step 2 above for optional "parallel strip application". This method gives you more surface area coverage. Install two or more strips in parallel and about an inch apart. Our research revealed that the ball of your foot will often find a landing between the parallel strips and give you superior non-slip confidence. However a single strip per step will also provide adequate traction.